Feed Using the App

Set Up Loader View (Android Only)

5 min

This feature is only available when you’re using this device for feeding. If you change your mind about using a device for feeding, log out of the app and select Yes or No when asked if the device will be used for feeding.

Before you can begin using FeedComp to feed at your dairy, you must complete the required setup. See Start Here: Better Feeding Made Simple to learn more about the required setup order.

Devices used for feeding must be connected to a scale. See Configure and Connect the Scale to learn more about connecting to your scale.

Bluetooth must be enabled on both loading and feeding devices.

🗒️ NOTE: Loader View is only supported on Android devices. See Mobile Device Requirements for a list of recommended Android devices.

Use Loader View to monitor and manage the loading of ingredients from a second mobile device while you're out feeding. Loader View lets the person operating the physical loader (tractor or payloader) use the second mobile device to see ingredient targets, track loading progress, and advance or pause feedings in real time — without walking over to the mixer device.

A Loader View setup uses two mobile devices:

Mixer device — the primary phone or tablet, mounted in or near the mixer, connected to the scale. Controls the overall feeding workflow.

Loader device — a second phone or tablet carried by the loader operator. Connects to the mixer device via Bluetooth to mirror loading actions.

💡 TIP: Bluetooth must be enabled on both devices. For best results, use devices dedicated to FeedComp (avoid pairing earbuds, smartwatches, or truck audio on the same device, since those connections can take priority and disrupt Loader View).

Follow the steps below to enable and start using Loader View:

Before you can use Loader View, create a "Loader" entry in FeedComp's Equipment list. This entry isn't a physical piece of equipment — it's a profile that tells FeedComp which mobile device will act as the loader operator's device.

Go to the Adjustments screen.

Tap Equipment.

Tap Create Equipment at the bottom of the screen.

Enter the following information for the loader:

Equipment Name: It must be unique and cannot match the name of existing equipment.

Equipment Type: Select Loader.

Audio Trigger Weight: Enter the scale weight that activates a sound notification. These sounds notify your technician when a specific ingredient weight is reached while mixing or a load of feed is almost done dropping at a pen. Sounds allow technicians to feed more efficiently because they won't need to look at the scale and/or mobile device while feeding.

Audio Settings: Tap + Add Sound to select the sound that plays when the scale reaches the Audio Trigger Weight and configure its playback settings. See Enable Sounds to learn more about adjusting the settings.

Tap Save at the bottom of the screen.

After you finish adding loader equipment to FeedComp, connect the loader equipment to FeedComp.

After you add loader equipment to the Equipment list, choose the loader equipment type from the loader device:

Go to Account Settings > Settings.

Select the loader equipment.

Save your selection and exit Settings.

💡TIP: Loader View pairing connects two mobile devices to each other via Bluetooth — this is different from pairing a scale to the FeedComp app. For a side-by-side comparison, see Bluetooth Pairing in FeedComp.

If pairing devices for the first time using Loader View, you need to pair the two Android devices together via Bluetooth first. To do this:

Open Bluetooth settings on both tablets.

Make sure Bluetooth is turned on.

On the mixer device name, select Pair new device.

Tap the name of the loader device.

When a pairing code displays on both screens, confirm it matches and tap Pair on both tablets.

Once the tablets are paired, you can connect a loading device to a feeding device within FeedComp and start using Loader View.

IMPORTANT: For Loader View to work properly, confirm the following requirements:

Loader equipment must be added and connected to FeedComp

The mixer device must be connected to a scale.

A feeding must be started on the mixer device.

After you complete the requirements above, follow the steps below to enable Loader View, so you can connect your loader device to your mixer device:

On the mixer device, tap Feed at the bottom of the screen.

Select a feeding and tap Start Mix at the bottom of the screen.

On the loader device, tap Feed at the bottom of the screen.

Tap Loader View.

Select the mixer device, and then tap Connect at the bottom of the screen.

Tap Continue at the bottom of the screen or wait for the screen to automatically display the mix on the loader device.

After establishing the connection, you can view and manage loading of ingredients from your loader device.

Summary:

The mixer device connects to the scale on the mixer.

The loader device using Loader View connects to the mixer device.

After you enable Loader View, monitor and manage loading from your loading device:

Load the first ingredient for the mix. As you load ingredients, the scale weighs the load and FeedComp calculates the percentage complete. You can Skip or Ignore ingredients if needed. If the weight of an ingredient detected by the scale drops below the threshold set for the mixer while mixing a recipe, FeedComp displays an alert that requires attention before adding the next ingredient to the mixer. To set the threshold, see Create New Equipment and Edit Equipment. Tap Acknowledge to confirm and record the ingredient's actual amount and continue mixing. Acknowledged ingredients are identified with an ACK icon on the Feed History Report.

If a timer was set for the ingredient, wait for the timer to complete. Or, tap Advance this Ingredient to move to the next step in the recipe.

If a time delay was set between ingredients, FeedComp displays a countdown in the middle of the screen for the allotted time. You can tap Skip to immediately move to the next ingredient in the recipe.

Once all of the ingredients are added and the progress bar reaches 100%, FeedComp automatically disconnects your device from the feeding device and returns you to the Home Inline image screen. The feeding technician can now drop the mix at the necessary locations.

Once the loading process is started for a feeding, you can tap Inline image Abort at the top middle of the screen to abort the feeding. Feedings started but not completed are identified with an Aborted icon on the Feed History Report.

Updated 19 Oct 2026

Loading and Dropping

Use Overnight Loads

Set Up Loader View (Android Only)

Required Setup

Add Loader Equipment in FeedComp

Choose Loader Equipment in FeedComp

Pair Loader View Devices via Bluetooth

Connect Loader Device to Mixer Device in FeedComp

Summary:

Load Ingredients into the Mixer

Abort a Feeding in Progress